Given the bearing numbers and the fact that it's a 6 bolt hub, you're needing the Dexter # 42660UC1 Agricultural hub. The bearings, races and seals are sold separately. You'll need the # 25580 inner bearing, the # LM67048 outer bearing, the # 25520 inner race and the # LM67010 outer race. The grease seal we carry that cross-references to the SKF 21352 is part # GS-2125DL.
This hub is typically used with the # GS-2250DL grease seal, so I'd recommend you use a digital caliper on the surface... view full answer...
The correct replacement tarp for your 2008 Ford F-250 short bed with a Truxedo Lo Pro tonneau is the part # TX569101-CVR since the cover you have would be the # TX569101. view full answer...
I contacted Lippert on your behalf. If this is the original triple step motor that came with the motor home, the update kit/Replacement Motor with Table for Kwikee 25 Series Electric RV Steps # LC379804 is what they recommended.
Included is a video overview with additional information on this solution. view full answer...
There are a lot of options for your trailer. I have attached the options for the axle replacement with the spring centers at 58 inches on center. The hangers, leaf springs, equalizers, shackle straps, and hardware. It would be very uncommon to not have a trailer with some sort of suspension are you sure you don't have a torsion axle with an arm that moves with the "springs" on the inside of that assembly?
I have also attached the information for the axle-less system which has the integrated... view full answer...
I'll start this off by saying that trailer wiring does not have any standard colors; so it's possible that your trailer just has different color wiring on it. The question you're referencing refers to the different colors of the wires on the magnets and is just an easy way to determine the difference between the # BP01-265 (white wires) which fit brake assemblies 12-1/4" x 2-1/2" and 12-1/4" x 3-3/8"-which are typically found 7k or 8k axles. Conversely the # BP01-301 (yellow wires) is designed... view full answer...
I spoke with my contact at Swagman. He stated that the pin used on the Trailhead 3 Bike Rack, # S63365, is a 1/2 inch diameter pin. The Wire Lock Pin, # 2471, that you have referenced is a 1/2 diameter pin. The 3-1/2 inch length is plenty long enough to fit the Swagman rack, so you can use it as a replacement. To verify, just measure from the outside of the hole where the pin goes to the outside of the opposite hole. The distance should be less than 3-1/2 inches. view full answer...
For an E-series step bar, you would need Replacement E-series Step Pad, # 23-0001. This pad requires 5 Barrel Clips, # 23-0002.
Specific bars use specific pads and clips so you will want to be sure of which style bar you have. The E-series bars are 3 inches in diameter and are either polished stainless steel or black powder coated. view full answer...
Yes, the left rear leg for the Lippert Ground Control 3.0 Electric 4 Point Leveling System is the same as the left middle leg for the Lippert Ground Control 3.0 Electric 6 Point Leveling System. If your left middle leg measures 17" long then you will need part # LC342610 but if it measures 19" long then you will need to use part # LC305339. The legs all have a one year warranty through Lippert. view full answer...
Your 2006 Toyota Tundra with the Double Cab and 6-foot bed uses the Extang Trifecta 2.0 tonneau cover # EX92850.
For the 2.0 cover you will use Replacement Tarp # EX92635-20. We also have the Replacement Tailgate Hinge # EX1033, Corners # EX4211 and Tail Clamp Assembly # EX31003005.
If you need other parts please let us know which specific items those are. Also please keep in mind that the Extang lifetime warranty includes parts such as bed cover rails, aluminum components, clamps, bows,... view full answer...
The CIPA ATV Handlebar Mirror - Black # CM11132 does not have any replacement parts from the manufacturer. Unfortunately you will need to replace the entire mirror since the wedge nut has been stripped. view full answer...
Thank you for your VIN. I was able to use this and determine that you need the Bearing Kit part # BK1-150. This kit has everything that you need to rebuild one hub so you will need two per axle. If you don't already have a bearing packer and grease you can use both part # PTW1218 and part # L54FR. view full answer...
The Wesbar 108121 has been discontinued but the Optronics Trailer Tail Light - Stop, Turn, Tail - Submersible - Incandescent - Oval - Red Lens # ST70RB is the ideal replacement. It works with the PVC Grommet for 6-1/2" Oval Trailer Tail Lights # A70GB. This light will use the standard 3 prong plug that if you need a replacement is # A45PB or # A47PB for the 90 degree connector. view full answer...
If you have the Extang BlackMax Soft Tonneau Cover part # EX2790 on your 2008 Ford F-150 with the 6-1/2' long bed then the correct replacement for you is the Replacement Tarp for Extang BlackMax Soft Tonneau Cover part # EX1790. view full answer...
If you have a 4-speed motor then you most likely have either the MaxxAir MaxxFan Mini or the MaxxAir MaxxFan. Therefore, the correct replacement operator for you is gong to be part # MA10-20281K-3CF if you have a manual lift vent lid or part # MA10-20281K-1AF if you have a powered lift vent lid. view full answer...
The Bearing Kit for #84 Spindle, L44649/L68149 Bearings, 10-19 Double Lip Seal # BK2-100 is very standard for your bearing combination. The seal however is 2.565 inches outer diameter and 1.719 inner diameter. This is by far the most common combination that fits most 3,500 lb axles.
The best way to check your actual seal requirements is to use a digital caliper for even more precision. You will measure the inside lip of your hub at the seal and then your trailer spindle at the seal... view full answer...
Individual parts from the Westin Installation Hardware Kit # 23-110PK referenced in your question are unfortunately not available from the manufacturer by themselves. If you need only one or a few of the included parts then you will need to obtain the entire kit.
This will at least give you spare parts for your Nerf Bars if anything else were to need replacement further down the line. This particular kit is designed to replace the mounting hardware for the Westin E-Series Round Nerf Bars... view full answer...
For your Ventadome V2094 fan, I am glad you were able to find the Replacement Screen Frame with Screen, Rocker Switch, and Wire for Ventline Roof Vents - Birch White # BVC0573-31R or for just the screen # BVD0434-31. The proper ceiling garnish for your vent will depend on your roof thickness. We have the following that are all confirmed to fit:
Ceiling Garnish for Ventline Roof Vent - 5-1/8" Leg - 14-1/4" x 14-1/4" - Birch White # VA0445-29
Ceiling Garnish for Ventline Roof Vent - 4-1/4"... view full answer...
The Wesbar Mini Clearance and Side Marker Trailer Light part # 203233 is a submersible light therefore, the bulb cannot be replaced without braking the seal. If you don't mind breaking the seal to change out the bulb then you can do so with a 193 bulb but otherwise you would need to replace the entire light if the bulb goes out. view full answer...
The sure way to match up a replacement 4-on-4 idler hub to your spindle is to note the bearing and seal part numbers from the original hub. On the linked page you'll see all 4-on-4 idler hubs and all of these use one of two bearings for both their inner and outer bearings, either # L44643 or # L44649.
We also offer complete axle/idler hub kits in both 60-inch and 72-inch hub face sizes and these complete axle kits like # 20440I-EZ-60 are shown on the linked page. This kit includes the... view full answer...
The correct replacement 5th wheel hitch head for Reese 30032 is part # RP30047A. This item includes the head, cross member, handle and hardware. All components are shown in the linked photo. view full answer...
Go To Results